Cellular PVC Sills: Where They Work and How to Install Them

A cellular PVC sill works well as a finishing and water-shedding profile at the base of a window, as long as it is fixed through the board at the right spacing, left free to move lengthwise, and painted in a light-reflective colour. It does not rot and takes almost no water, but it is a trim product: it cannot be used structurally, and the wall detail behind it still has to keep water out.

What is a cellular PVC window sill, and where does it fit?

Cellular PVC is a foamed vinyl board sold as exterior trim, and several makers offer a window sill moulding in it. One manufacturer describes its sill moulding as a way to give a finished look at the base of the window opening and direct water away from it. The product claims are consistent across makers: it does not rot or attract termites, resists splitting and cracking, absorbs virtually no water, and can be cut with ordinary woodworking tools.

It fits best where you want a clean, paintable sill profile on a wall that is already weather-tight: renovation of an existing window, a trim package around new vinyl or aluminium windows, or a porch or garage opening. It is a poor choice if you expect it to carry loads or to be the only water barrier. For the wider choice of materials, slopes and drip edges, see our guide to exterior window sill trim.

How much does cellular PVC move, and how do you allow for it?

PVC expands and contracts mainly along its length, not its width. The practical rules published by trim makers are these:

  • Install temperature: 60 to 70°F (about 15 to 21°C) is ideal for long runs. A trim carpenter reported a gap of about 3/16 in. opening by midwinter after boards were installed at 90°F.
  • Expansion gap: one manufacturer's guide gives about 1/8 in. per 18 ft run when installing between 50 and 90°F, and 3/16 in. below 50°F. Above 90°F, join the pieces tight.
  • Sealant: never fill the gap completely, and avoid silicone caulk. Use a flexible sealant made for PVC.
  • Sun: south-facing or dark-painted runs move more, so add fasteners and plan longer gaps.

A single sill rarely runs 18 ft, but a trim package with long horizontal bands does, and the same rules apply to each piece.

How should it be fixed and joined?

Use stainless or hot-dipped galvanised nails, or corrosion-resistant trim-head screws. Manufacturer guidance is to penetrate about 1½ in. into solid framing, keep fasteners between ¾ in. and 2 in. from the board end, and double up on both sides of a joint. For boards 4 to 6 in. wide, a common schedule is two fasteners every 16 in.; 8 to 10 in. boards take three. Adhesive alone must not hold the trim.

For joints, one manufacturer says not to butt-join boards and to use a shiplap or a 45-degree mitre, glued with PVC cement, while a magazine article describes hiding movement with butt joints at inside corners. Where makers and installers disagree, follow the data sheet of the product you buy. Where water has to be kept out behind a joint, add aluminium or vinyl flashing.

Which paint colours are safe on cellular PVC?

Use 100 % acrylic latex paint. The key number is the light reflectance value (LRV), from 0 (black) to 100 (white): both the magazine article and the manufacturer's guide say paint with an LRV under 55 is a problem on PVC trim, because dark colours absorb enough solar heat to cause failure, and the wrong paint can void the warranty. For darker colours, the manufacturer points to vinyl-safe paints made for the purpose. Scuff sand lightly first and check whether your trim maker requires a primer: cellular PVC cement itself needs none.

Cellular PVC or another sill material?

Choose by what the wall and the budget need rather than by habit. Cellular PVC does not rot and needs only repainting. One contractor's report put its price at roughly twice finger-jointed pine, in 2005, so check current local prices. Stone or concrete suits a masonry sill that must carry weight and shed water on its own slope; a PVC profile suits a trim role over a sound, sloped substrate. If you simply want a relief-rich decorative sill look on a facade, a moulded sill product such as our decorative window sills is a different category, and the same rule applies: slope and flashing come first, finish second.

Sources

Frequently Asked Questions

Does cellular PVC rot or absorb water?+
Makers state that it does not rot, does not attract termites and absorbs virtually no water, which is why it is used for exterior sills and trim.
Can I paint cellular PVC a dark colour?+
Only with a paint made for it. Guidance from a trim maker and a building magazine says to avoid paints with an LRV below 55 unless they are vinyl-safe formulations, because dark colours build up heat.
Can I use silicone caulk on PVC trim joints?+
One manufacturer's guide says not to use silicone caulk and never to fill the expansion gap completely; use a flexible sealant made for PVC.
Is PVC trim structural?+
No. Manufacturers state it cannot be used structurally, so the sill needs a sound, sloped support behind it.